Emissions And Stack Function Generators

Features

• 2 Channel Digital Oscilloscope + 1

• Channel Arbitrary or Function

• Waveform Generator +

• Synchronizing Signal + External Trigger

• The Keys for oscilloscope and waveform

• Generator is separated for convenient

• Operate it simultaneously

• Oscilloscope: 1 GSa/s

• Sample Rate,100 MHz Bandwidth

• 20 kinds of auto measurement functions

• Powerful Trigger Function: Edge, Video,

• Pulse, Slope, Over time, Alternative;

• Arbitrary or Function Waveform

• Generator: 25 MHz, 12 bits resolution

• Support SD card, VGA function (optional);

• Integrated USB Host,

• Support USB disk storage,

• USB interface or SD card system update

 

Technical Specifications

Sample Rate	Sampling Rate Range: 1 GSa/s Equivalent Sample Rate: 25 GSa/s
Acquisition Modes
Normal	Normal data only
Peak Detect	High-frequency and random glitch capture
Average	Waveform Average, selectable 4,8,16,32,64,128
Inputs Coupling	AC, DC, GND
Inputs Impendence	1 MΩ ±2 % 20 pF±3 pF
Probe Attenuation	1 x, 10 x
Supported Probe Attenuation Factor	1 x, 10 x, 100 x, 1000 x
Maximum Input Voltage	CAT I and CAT II: 300 VRMS (10×) CAT III: 150 VRMS (1×); Installation Category II: derate at 20dB/decade above 100 kHz to 13 V peak AC at 3 MHz x and above. For non-sinusoidal waveforms, peak Value must be less than 450 V. Excursion above 300 V should be of less than 100 ms duration. RMS signal level including all DC Components removed through AC coupling must be limited to 300 V. If these values are exceeded, damage to the oscilloscope may occur.
Sample Rate Range	1 GS/s
Waveform Interpolation	(sin x) or x
Record Length	40 K
SEC or DIV Range	2 ns or div to 40 s or div
Sample Rate and Delay Time Accuracy	±50 ppm (at over any ≥1 ms time interval)
Position Range	2 ns or div to 8 ns or div;  20 ns or div to 80 us or div; (-8 div x s or div) to 40 ms; (-8 div x s or div) to 20 ms; 200 us or div to 40 s or div; (-8 div x s or div) to 400 s
Delta Time Measurement Accuracy	Single shot, Normal mode: ± (1 sample interval +100 ppm × reading + 0.6 ns);
(Full Bandwidth)	>16 averages: ± (1 sample interval + 100 ppm × reading + 0.4 ns);
	Sample interval = s or div ÷ 200
Vertical
Vertical Resolution	8-bit resolution, all channel sampled simultaneously
Position Range	2 mV or div to 10 V or div
Bandwidth	200 MHz,100 MHz,70 MHz
Rise Time at BNC (typical)	1.8 ns,3.5 ns, 5 ns
Offset Range	2 mV or div to 20 mV or div, ±400 mV; 50 mV or div to 200 mV or div, ±1 V 500 mV or div to 2 V or div, ±40 V; 5 V or div to 10 V or div, ±50 V
Math	+, -, x, or FFT
FFT	Windows: Hanning, Flattop, Rectangular, Bartlett, Blackman; 1024 sample point
Bandwidth Limit	20 MHz
Low Frequency Response (3db)	≤10 Hz at BNC
DC Gain Accuracy	±3 % for Normal or Average acquisition mode, 10 V or div to 10 mV or div; ±4 % for Normal or Average acquisition mode, 5 mV or div to 2 mV or div
DC Measurement Accuracy,	When vertical displacement is zero, and N ≥16: ± (3 % × reading + 0.1 div + 1 mV) only 10mV/div or greater is selected;
Average Acquisition Mode	When vertical displacement is not zero, and N≥16: ± [3 % × (reading + vertical position) + 1% of vertical position+ 0.2 div]; Add 2 mV for settings from 2 mV or div to 200 mV or div; add 50 mV for settings from 200 mV or div to 10 V or div
Volts Measurement Repeatability, Average Acquisition Mode	Delta volts between any two averages of ≥16 waveforms acquired under same setup and ambient conditions